Multiple Choice Questions Paper Junior Engineer RRB Green Part II (75 questions) Year 2014
During 2014 examination of JE/RRB multiple choice question paper, there were three sets of questions paper called Yellow, Green and Red. This is set of green question paper for your on-line mock drill test. There are 150 questions to be attended in 120 minutes. Due to software issue, there will be two posts of 75 questions each.You should take up the second set of 75 questions immediately. Sitting for 120 minutes and attempting for widely varying subject of 150 questions is very strenuous. This question paper was somewhat difficult but is for all those appearing in the examination.
Out the 75 questions, one is given below with answer, and balance 74 is for mock drill
Question: If the value of (10)½ = 3.1623 (approximately) then what is the approx. value of (10)-½ ?
Options: (A) 0.333 (B) 0.3162 (C) 0.3221 (D) 0.3437
Answer: (B)
Mock drill will help you
- Building stamina to sit for 120 minutes and concentrate
- If you get stuck up, learn to leave the question instead waiting for miracle to happen
- The calculation in every arithmetic question will always be simple. If you find it difficult, it means you are attempting wrongly.
- The previous year question paper will help you to understand the wide range of syllabus, type of questions, standard of question and most importantly how to prepare your self.
- The mock drill exercise will help in building up the physical and mental stamina
- The standard of JE is difficult as compared to SSE. Therefore, attempt all the mock drills on this site.
Quiz-summary
0 of 74 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
Information
This is Set II (Green) of 75 multiple choice question of the RRB examination of SSE/JEE held in Dec. 2014.
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 74 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
-
The Answer Key:
Sr No Question Answer Remarks 1 The Hindustan Shipyard Limited is located at Visakhapatham 2 In India, what is the minimum permissible age for employment in a factory ? 14 years 3 Lunar Eclipse occurs only on a Full moon day 4 Mirages generally occur in deserts 5 Which state is known for its sandalwood carvings ? Karnataka 6 Section 66 A has been in media controversy recently. The section pertains to Information Technology. 7 IPC stand for Indian Penal Code 8 Who among the following can accept the deposits of money from the public, as a business in financial transactions ? None of the above 9 NEFT and RTGS are the means for Money transfer 10 In Sept. 2014 ISRO achieved success in which project ? Mars Orbiter successfully entered mars orbit 11 In October 2014 a cyclone hit Vishakhapatnam. The name of the cyclone was Hudhud 12 SAARC countries are from which part of the world ? South Asia 13 How many pairs of letters are there in the word CRAB which has as many letters between them in the word as there are between them in the English alphabet ? 2 14 Which month is different from other months in the group ? July 15 If circumference of a circle is increased by 10%, the area of the circle will increase by 0.21 16 A cylindrical shaped metal piece is converted into a wire. Out of the following which parameter can be assumed to remain the same ? volume 17 What is the probability of getting 3 aces if three cards are drawn from a set of 52 playing cards ? 4x3x2/52x51x50 18 In a class of 40 students, 25 are sports persons and 25 are mathematicians. What is the probability that the monitor of the class is both a sports person and a mathematician ? ¼ 19 Sum of two numbers is 15 and sum of their reciprocals is 15/56. The two numbers are 7,8 20 If a, B are the roots of quadratic equation x² + x +1 = 0, then -1 21 Value of √6+√6+√+………….is 3 22 If a,b,c,d,e and f are in arithmetic progression, then e-c is equal to 2 (b-a) 23 In coordinate geometry, distance of the point (-4,3) from origin is 5 24 Find the median of the following numbers 14 23 20 12 11 15 24 17 9 21 25 17 25 tan 90ᵒ is undefined. As Ø is increased from 89ᵒ towards 90ᵒ, value of tan Ø tends to #ERROR! 26 A man sells his two cars at the same price. In one car he makes a profile of 10%. In other car he loses 10% over the cost price. His total gain or loss percent is 1%less 27 0.3162 28 A student was asked to multiply a number by 12. By mistake he multiplied the number by 21 and got the answer 63 more than the correct answer. What is the correct answer ? 84 29 Consider the following graph : Which portion represents the ‘Latent Heat of fusion’ OA 30 Which of the following does not sublimate ? Ice 31 Which of the following is a heterogeneous mixture ? Milk 32 A class of compounds which are used as fragrances when molecular weight is low and are naturally occurring fats when molecular weight is high in the series, is called esters 33 If the mass of sun, earth and distance between them is respectively M, m and r; done by the sun’s gravity on earth for one revolution round the sun is zero 34 The choke of a tube light works on the principle of inductance 35 In the figure below, what is the acceleration of body with mass m2, given g is the acceleration due to gravity (assume pulley and surfaces are smooth) 36 Which of the following statements is correct ? All of the above 37 In Heisenberg’s Uncertainty principle, the uncertainty of momentum and position of a particle can be can’t be reduced as it is fundamentally inherent. 38 In scooter, in which part is the petrol atomized and mixed in correct proportion with air ? Carburettor 39 Which alloy steel would be used for making leaf and coil springs ? Silicon-Manganese 40 In aluminium casting bubbles of argon or nitrogen are passed through the molten metal to remove hydrogen gas porosity 41 Clearance between the mating parts is measured using Feeler gauge 42 In a milling process, for milling mild steel, what will be a typical rake angle for the cutter ? 12ᵒ 43 State True (T) or False (F) respectively. 1. For better tensile strength, caste component is preferred over forged component 2. Quenching of hot iron component in water improves its malleability F, F 44 Channels, Angles and I -section, which are used in fabricating a shed structure frame, are manufactured from blooms using the process of rolling 45 Output of a welding transformer, compared with its input is low voltage high current 46 A fuse should be connected in ————in the ———-conductor. series, live 47 Equipment earthing gives protection against: electric shocks 48 A generator is rated 2 KW 200 V.D.C. It can supply load current of : 49 The term PCB stands for Printed Circuit Board 50 Colour bands for 1.5 ohms resistor will be Brown, Green, Golden 51 A frequency tuning electronic circuit would consist of : an inductor and a capacitor 52 Main element of a filter circuit that reduces the A.C. component of the output is : capacitor 53 For stabilising the gain of an amplifier: negative feedback is used 54 A stereophonic system requires: all of the above. 55 For plastering walls, cement mortar would be typically used in which ratio ? Sat Dec 30 1899 00:40:40 GMT+0530 (IST) 56 The grade M25 of concrete would approx. refer to the mix: Sat Dec 30 1899 00:37:42 GMT+0530 (IST) 57 Brass is an alloy of : copper and zinc 58 A pigment generally used to impart white colour in a paint is: zinc 59 The main purpose of providing foundation to a building is : to distribute the weight of the structure on a sufficiently large area of the substratum 60 The branch of surveying in which only linear measurements are directly made in the field is : chain surveying 61 A theodolite is used for measuring: angles 62 Contour lines drawn on a map, are the lines which pass through: same elevation 63 Which of the following statements is incorrect ? More than 5000 kB data can store 2 million files each of size 1 MB. 64 How many lines can be said to exist or be drawn in a three dimensional space, which are mutually perpendicular to each other ? 3 65 A third angle orthographic projection of an object is given below. What is this object? Frustrum of a cone 66 In an engineering drawing it is written scale 1 cm = 100 m. Which ratio does it correspond to ? 67 In machine drawing, a ‘sectional view’ cut portion is shown by: diagonal hatching 68 For complete description of a component, a machine drawing would require minimum how many orthographic projections ? 2 69 Thermochemical decomposition of organic materials at high temperatures, in the absence of oxygen is called : Pyrolysis 70 Acid rain is caused by presence of which of the following gases in the atmosphere: Sulphur dioxide and Carbon-mono-oxide 71 One of the main reason for depletion of ozone layer in the Earth’s atmosphere is: CFC and halons 72 What is the value of total hardness acceptable in potable water as per Indian Standards ? 300 73 Preventing rain water to run-off and its accumulation and deposition for re-use on site is called : rain water 74 The terms ALU, CPU, I/O devices pertain to: computers 75 In a computing device ‘MHz’ is mentioned in the specifications. It refers to: clock speed -
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- Answered
- Review
-
Question 1 of 74
1. Question
If the mass of sun, earth and distance between them is respectively M, m and r; work done by the sun’s gravity on earth for one revolution round the sun is
-
Question 2 of 74
2. Question
The Hindustan Shipyard Limited is located at
-
Question 3 of 74
3. Question
In India, what is the minimum permissible age for employment in a factory ?
-
Question 4 of 74
4. Question
Lunar Eclipse occurs only on a
-
Question 5 of 74
5. Question
Mirages generally occur in
-
Question 6 of 74
6. Question
Which state is known for its sandalwood carvings ?
-
Question 7 of 74
7. Question
Section 66 A has been in media controversy recently. The section pertains to
-
Question 8 of 74
8. Question
IPC stand for
-
Question 9 of 74
9. Question
Who among the following can accept the deposits of money from the public, as a business in financial transactions ?
-
Question 10 of 74
10. Question
NEFT and RTGS are the means for
-
Question 11 of 74
11. Question
In Sept. 2014 ISRO achieved success in which project ?
-
Question 12 of 74
12. Question
In October 2014 a cyclone hit Vishakhapatnam. The name of the cyclone was
-
Question 13 of 74
13. Question
SAARC countries are from which part of the world ?
-
Question 14 of 74
14. Question
How many pairs of letters are there in the word CRAB which has as many letters between them in the word as there are between them in the English alphabet ?
-
Question 15 of 74
15. Question
Which month is different from other months in the group ?
-
Question 16 of 74
16. Question
If circumference of a circle is increased by 10%, the area of the circle will increase by
-
Question 17 of 74
17. Question
A cylindrical shaped metal piece is converted into a wire. Out of the following which parameter can be assumed to remain the same ?
-
Question 18 of 74
18. Question
What is the probability of getting 3 aces if three cards are drawn from a set of 52 playing cards ?
-
Question 19 of 74
19. Question
In a class of 40 students, 25 are sports persons and 25 are mathematicians. What is the probability that the monitor of the class is both a sports person and a mathematician ?
-
Question 20 of 74
20. Question
Sum of two numbers is 15 and sum of their reciprocals is 15/56. The two numbers are
-
Question 21 of 74
21. Question
If α and β are the roots of quadratic equation x² + x +1 = 0, then (1/α)+(1/β) is
-
Question 22 of 74
22. Question
-
Question 23 of 74
23. Question
If a,b,c,d,e and f are in arithmetic progression, then e-c is equal to
-
Question 24 of 74
24. Question
In coordinate geometry, distance of the point (-4,3) from origin is
-
Question 25 of 74
25. Question
Find the median of the following numbers 14, 23, 20, 12, 11, 15, 24, 17, 9, 21, 25
-
Question 26 of 74
26. Question
Tan 90ᵒ is undefined. As Ø is increased from 89ᵒ towards 90ᵒ, value of tan Ø tends to
-
Question 27 of 74
27. Question
A man sells his two cars at the same price. In one car he makes a profile of 10%. In other car he loses 10% over the cost price. His total gain or loss percent is
-
Question 28 of 74
28. Question
A student was asked to multiply a number by 12. By mistake he multiplied the number by 21 and got the answer 63 more than the correct answer. What is the correct answer ?
-
Question 29 of 74
29. Question
-
Question 30 of 74
30. Question
Which of the following does not sublimate ?
-
Question 31 of 74
31. Question
Which of the following is a heterogeneous mixture ?
-
Question 32 of 74
32. Question
A class of compounds which are used as fragrances when molecular weight is low and are naturally occurring fats when molecular weight is high in the series, is called
-
Question 33 of 74
33. Question
The choke of a tube light works on the principle of
-
Question 34 of 74
34. Question
-
Question 35 of 74
35. Question
Which of the following statements is correct ?
-
Question 36 of 74
36. Question
In Heisenberg’s Uncertainty principle, the uncertainty of momentum and position of a particle can be
-
Question 37 of 74
37. Question
In scooter, in which part is the petrol atomized and mixed in correct proportion with air ?
-
Question 38 of 74
38. Question
Which alloy steel would be used for making leaf and coil springs ?
-
Question 39 of 74
39. Question
In aluminium casting bubbles of argon or nitrogen are passed through the molten metal
-
Question 40 of 74
40. Question
Clearance between the mating parts is measured using
-
Question 41 of 74
41. Question
In a milling process, for milling mild steel, what will be a typical rake angle for the cutter ?
-
Question 42 of 74
42. Question
State True (T) or False (F) respectively. 1. For better tensile strength, caste component is preferred over forged component 2. Quenching of hot iron component in water improves its malleability
-
Question 43 of 74
43. Question
Channels, Angles and I -section, which are used in fabricating a shed structure frame, are manufactured from blooms using the process of
-
Question 44 of 74
44. Question
Output of a welding transformer, compared with its input is
-
Question 45 of 74
45. Question
A fuse should be connected in ————in the ———-conductor.
-
Question 46 of 74
46. Question
Equipment earthing gives protection against:
-
Question 47 of 74
47. Question
A generator is rated 2 kW 200 V D.C. It can supply load current of :
-
Question 48 of 74
48. Question
The term PCB stands for
-
Question 49 of 74
49. Question
Colour bands for 1.5 ohms resistor will be
-
Question 50 of 74
50. Question
A frequency tuning electronic circuit would consist of :
-
Question 51 of 74
51. Question
Main element of a filter circuit that reduces the A.C. component of the output is :
-
Question 52 of 74
52. Question
For stabilising the gain of an amplifier:
-
Question 53 of 74
53. Question
A stereophonic system requires:
-
Question 54 of 74
54. Question
For plastering walls, cement mortar would be typically used in which ratio ?
-
Question 55 of 74
55. Question
The grade M25 of concrete would approx. refer to the mix:
-
Question 56 of 74
56. Question
Brass is an alloy of :
-
Question 57 of 74
57. Question
A pigment generally used to impart white colour in a paint is:
-
Question 58 of 74
58. Question
The main purpose of providing foundation to a building is :
-
Question 59 of 74
59. Question
The branch of surveying in which only linear measurements are directly made in the field is :
-
Question 60 of 74
60. Question
A theodolite is used for measuring:
-
Question 61 of 74
61. Question
Contour lines drawn on a map, are the lines which pass through:
-
Question 62 of 74
62. Question
Which of the following statements is incorrect ?
-
Question 63 of 74
63. Question
How many lines can be said to exist or be drawn in a three dimensional space, which are mutually perpendicular to each other ?
-
Question 64 of 74
64. Question
-
Question 65 of 74
65. Question
In an engineering drawing it is written scale 1 cm = 100 m. Which ratio does it correspond to ?
-
Question 66 of 74
66. Question
In machine drawing, a ‘sectional view’ cut portion is shown by:
-
Question 67 of 74
67. Question
For complete description of a component, a machine drawing would require minimum how many orthographic projections ?
-
Question 68 of 74
68. Question
Thermochemical decomposition of organic materials at high temperatures, in the absence of oxygen is called :
-
Question 69 of 74
69. Question
Acid rain is caused by presence of which of the following gases in the atmosphere:
-
Question 70 of 74
70. Question
One of the main reason for depletion of ozone layer in the Earth’s atmosphere is:
-
Question 71 of 74
71. Question
What is the value of total hardness acceptable in potable water as per Indian Standards ?
-
Question 72 of 74
72. Question
Preventing rain water to run-off and its accumulation and deposition for re-use on site is called :
-
Question 73 of 74
73. Question
The terms ALU, CPU, I/O devices pertain to:
-
Question 74 of 74
74. Question
In a computing device ‘MHz’ is mentioned in the specifications. It refers to:
You may also like:
- Help to understand job profile of NTPC vacancies advertised by…
- Multiple choice questions on Mathematics for competitive examination Test 10
- Multiple choice questions on Mathematics for competitive examination Test 9
- Multiple choice questions on Mathematics for competitive examination Test 7
- Multiple choice questions on Mathematics for competitive examination Test 6
- Multiple choice questions on Mathematics for competitive examination Test 8