Multiple Choice Questions on Electrical Engineering and Practice Test 9
Last updated on October 31st, 2014 at 02:45 pm
There are 16 questions to be attended in 20 minutes. The questions are on Electrical Engineering. Read the study material before making an attempt so that you build your confidence in the subject. This is the ninth of the series of 10 questions paper that will appear before the RRB examination for SSE and JE to be held in Dec.
Quiz-summary
0 of 16 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
Information
There are 16 questions to be attended in 20 minutes. The questions are on Electrical Engineering. Read the study material before making an attempt so that you build your confidence in the subject. This is the first of the series of 10 questions paper that will appear before the RRB examination for SSE and JE to be held in Dec.
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 16 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
| Average score |
|
| Your score |
|
Categories
- Not categorized 0%
-
The Answer Key:
Sr No Question Answer Remarks 1 Lumen Efficiency is defined as Ampere 2 Increase in the resistance of a material due to increase in temperature is directly proportional to V/I Rt-R0=R0*α*δT 3 The current at any instant in an capacitor when connected to a DC source is given by lag the voltage applied 4 n number of resistances of each r ohms when connected in parallel found to have R ohms; what will be its value when connected in series sum of voltage drops and battery emf in a closed loop is zero When n resistances of value r are connected in parallel than R=r/n; and each will have a value of nR. This resistance when connected in series , the net value of n*nR=n²R 5 A parallel plate capacitor is charged to 24 V and its plate separation is 2 mm and area of each plate is 150 cm², what happens to its capacitance, if the plate separation is reduced to 1 mm? I*R*t C = ε*Area/distance between two plates; 6 The battery used in this system is generally on float charge PbO2 to PbSO4 The system comes into service only when there is a power supply failure which is very rare and generally the battery system remains on float charge 7 A RLC circuit is said to be at resonance when 270 Xc=Xl; resonant circuit is only resistive 8 What will be torque produced at 6% slip if the maximum torque produced is 200 Kg-m at 12% slip? increase in speed 9 A transmission line string insulator has 10 discs. What is the transmission voltage? 3-33kV 10 The inductance per km of a 11 kV distribution line is high cost 11 Area of trapezoidal curve depiction motion of a train from start to stop depicts MIG 12 Dielectric heating is by the transfer of energy doping Micro-wave uses the principle of dielectric heating 13 A perfect black body is one which 30 kV/cm 14 Increase in flux density in the transformer helps in Torque 15 Impedance protection is same as distance relay and works on the principle of measuring Moulded Case Circuit Breaker Distance protection detects both voltage and current. A fault on a circuit will generally create a sag in the voltage level. If the ratio of voltage to current measured at the relay terminals, which equates to an impedance, lands within a predetermined level the circuit breaker will operate. 16 A 200 mH inductor is connected across a supply for 100 V AC. For which of the following frequency the circuit will have highest rms current? 9 times Xl=2π*f*L and therefore, the Xl is minimum for minimum frequency
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- Answered
- Review
-
Question 1 of 16
1. Question
Area of trapezoidal curve depiction motion of a train from start to stop depicts
-
Question 2 of 16
2. Question
A 200 mHÊinductorÊis connected across a supply for 100 V AC. For which of the following frequency the circuit will have highest rms current?
-
Question 3 of 16
3. Question
n number of resistances of each r ohms when connected in parallel found to have R ohms; what will be its value when connected in series
-
Question 4 of 16
4. Question
Lumen Efficiency is defined as
-
Question 5 of 16
5. Question
Increase in the resistance of a material due to increase in temperature is directly proportional to
-
Question 6 of 16
6. Question
The current at any instant in an capacitor when connected to a DC source is given by
-
Question 7 of 16
7. Question
A parallel plate capacitor is charged to 24 V and its plate separation is 2 mm and area of each plate is 150 cm_, what happens to its capacitance, if the plate separation is reduced to 1 mm?
-
Question 8 of 16
8. Question
The battery used in this system is generally on float charge
-
Question 9 of 16
9. Question
A RLC circuit is said to be at resonance when
-
Question 10 of 16
10. Question
What will be torque produced at 6% slip if the maximum torque produced is 200 Kg-m at 12% slip?
-
Question 11 of 16
11. Question
A transmission line string insulator has 10 discs. What is the transmission voltage?
-
Question 12 of 16
12. Question
The inductance per km of a 11 kV distribution line is
-
Question 13 of 16
13. Question
Dielectric heating is by the transfer of energy
-
Question 14 of 16
14. Question
A perfect black body is one which
-
Question 15 of 16
15. Question
Increase in flux density in the transformer helps in
-
Question 16 of 16
16. Question
Impedance protection is same as distance relay and works on the principle of measuring
You may also like:
- Multiple Choice Questions on Electrical Engineering and Practice Test 5
- Multiple Choice Questions on Electrical Engineering and Practice Test 7
- Multiple Choice Questions on Electrical Engineering and Practice Test 8
- Multiple Choice Questions on Electrical Engineering and Practice Test 10
- Multiple Choice Questions on Electrical Engineering and Practice Test 6
- Multiple Choice Questions on Electrical Engineering and Practice Test 4
sir, i am having problem with the answers given, some of them r not even present in the options :(.
May i request to given the question where the problem is found so that I can correct it. There is some software problems.